Spark Tester Sensitivity Calibrator

Puretronics Spark Tester Sensitivity Calibrator ensures accurate calibration, enhancing safety and efficiency in testing electrical insulation systems for Wires and Cables

Puretronics introduces complete range of Spark Tester for Cable Extrusion Process to check the insulation quality of the wire being produced. For the testing the dry cable runs through the electrode thereby the cable being exposed to the Voltage set by the user. The device based on its senstivity and voltage detects the faults and puntures in the insulation of the cable.

Based on the application Mains Frequency AC Spark Tester (50-60Hz), High Frequency AC Spark Tester (2.5KHz-3.5KHz), DC Spark Tester are being used.

Its ease to operation, setup and integration with the system, makes it simplier for any operate the use the device efficiently and maintain it properly at the same time.

Features
Technical Specification
Accessory
Application - Insulation Testing

MFST (Mains Frequency Spark Tester)

Confirms to Major Standards
All digit digital display readout

2 Change Over relay output for different interlocks
Fault vs Length Graph and Data Logging (Optional)

HFST (High Frequency Spark Tester)

Confirms to Major Standards
All digit digital display readout
2 Change Over relay output for different interlocks

Fault vs Length Graph and Data Logging (Optional)
Stand with adjustable height based on the model
MOSFET based Sine wave low power circuit

DCST

Confirms to Major Standards fault detection at very high speed
Require very less space to install
Robust design
Absolutely fatal free to human
Easy Pin Hole Detection

All digit digital display readout
2 Change Over relay output for different interlocks
Fault vs Length Graph and Data Logging (Optional)
Stand with adjustable height based on the model

Model	MFST-15/25/40kv	HFST-10/15kv	DC-15/25kv
Voltage Range	1.5 to 15kv/25kv/40kv	1.5 to 15kv	1.5 to 15/25kv
Test Frequency	50/60hz (Same as supply Frequency)	2.5 to 3.5khz Sine wave A.C RMS	Direct Current
Wire Size	0.5 T0 40mm 0.D (60mm on demand)	0.5 to 15mm 0.D	0.5 to 15mm 0.D (30mm on demand)
Electrode	Bead chain housing of 350mm long	Bead chain housing of 70mm long	Bead chain housing of 70mm long
Max Wire Speed	200mts/min	2500mts/min	2500mts/min
H.V Meter	Digital LED	Digital LED	Digital LED
Sensitivity	Selectable position switch/Adjustable knob	As per standard	As per standard
Fault Counter	6 digit LCD Self Powered	6 digit LCD Self Powered	6 digit LCD Self Powered
Power Supply	230v AC 50/60 Hz, 1KVA	230v AC 50/60Hz, 0.5KVA	165 —200VAC, 0.5kVA
Interlocking	By potential free change over	By potential free change over	By potential free change over
Safety	Door interlocking	Door interlocking	Door interlocking
Adjustable wire Running height	950mm to 1100mm from ground level	900mm to 1100mm from ground level(With Stand Acc.)	900mm to 1100mm from ground level(With Stand Acc.)
Dimension in MM(15kv)	820W x 1160H x 460D	450W x 336H x 405D	282W x 252H x 270D
Approximate Weight(15kv)	80 Kg	20.4 Kg	7.94 kg

STAND-DCST	The stand is used for DCST-15KV/20KV to keep it steady during the production. The adjustable height of the stand makes it easier in case of interfacing it with different machine and different application.
STAND-HFST	The stand is used for HFST-10KV to keep it steady during the production. The adjustable height of the stand makes it easier in case of interfacing it with different machine and different application.